Dwyer SCD Manual de usuario descargar pdf (Pagina 8)

Address Setting Content Explanation

detail

102AH Read/Write status

b1:ALM2, b2:°C, b3:°F, b4: ALM1, b5: O2, b6:O1,

b7: AT

102CH 0

Setting of positive/negative

proportional output

0: positive, 1: negative

102EH LED status

b0: RUN,b1: ERR, b2: O2,b3: O1,b4: RX,b5:TX b6:

102FH Software version V1.00 indicates 0x100

1030H 0 Start pattern number 0 ~ 7

1032H Remaining time of read execution

Unit: second

1033H

Remaining time of reading

execution step

Unit: minute

1034H

Step number of reading current

execution step

0 ~ 7

1035H

Executing number of reading

current pattern

0 ~ 7

1037H 1000 Upper-limit of proportional output

0 ~100% max. analog output is upper limit, unit:

0.1%

1038H 0 Lower-limit of proportional output

0 ~ 100% max. analog output is lower limit, unit:

0.1%

1040H~

1043H

Actual step number setting inside

the correspond pattern

0 ~ 7 = N means the pattern is executed from step

from 0 to N.

1050H~

1053H

Cycle number of repeating

executing pattern 0~7

0 ~ 199 means the pattern is executed for 1 ~ 200

times.

1060H~

1063H

Link pattern number setting of the

current pattern

0 ~ 8, 8 means program end. 0 ~ 7 means the next

execution number after completing current pattern.

1068H 1 Control execution/Stop setting

0: Stop, 1: execute, 2: program end, 3: program

hold

1069H 0 Output 1: control selection

0: heating, 1: cooling, 2: alarming, 3: proportional

output

106AH 0 Output2: control selection 0: heating, 1: cooling, 2: alarming

106BH 0

Dismiss level 1

Read/write allowed

Shall be same as level 1 password setting (106E)

106CH 0 Dismiss level 2. Use level 3. Shall be same as level 2 password setting (106F)

106DH 0 Dismiss level 3. Use level 2 Shall be same as level 3 password setting (1070)

106EH 0 Dismiss level 1/Set password Clear old password before new password setting

106FH 0 Dismiss level 2/Set password Clear old password before new password setting

1070H 0 Dismiss level 3/Set password Clear old password before new password setting

1071H 1

Read/Write communication

address

1 ~ 247

1072H 0

Read/Write communication

format

RTU: 1, ASCII: 0

1073H 2

Baud rate setting of

communication

0 ~ 4: 2400 ~ 38400

1074H 1

Data length setting of

communication

0: 8bit 1: 7bit

1075H 1 Parity bit setting 0: None 1:Even 2: Odd

1076H 1 Stop bit setting 0: 2 stop bit 1: 1stop bit

2000H~

203FH

Pattern 0 ~ 7 to set target

temperature

Pattern 0: 2000H ~ 2007H

Temperature measure unit: 0.1 degree

2080H~

20BFH

Pattern 0 ~ 7 to set execution

time.

Pattern 0: 2080H ~ 2087H

Time 0 ~ 900 (1 minute for each scale)

1 2 3 4 5 6 7 8 9 10

Comentarios a estos manuales

Sin comentarios

Dwyer SCD Manual de usuario Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Dwyer SCD